Friday, September 23, 2011

2006 Ford Focus Signal and Tail Light Issue?

I've been working on a 2006 Ford Focus for a few days trying to find the source of an electrical problem in the lights. The running lights work in the back, the tail lights that is when you are driving down the road, but when you apply brakes the rear right light does not respond. The turn signal on the rear right side doesn't work either. I have checked the fuses 42 (stop lamps), 30 (parking lamps), and 32 (turn signal) but there was nothing wrong with the fuses for the lights. I also tried changing the bulbs, but that wasn't the problem either. The running lights still work on the rear right corner, but the brake light and turn signal light do not work on the rear right tail lights. I can't figure out what the problem is. Electricity is reaching the brake light, but it doesn't work. The front turn signal on the right side works, but it is blinking very rapidly now that the one on the right in the back does not work. Please help me figure out the problem. The dealership wants to charge several hundred to fix and they want to keep the car for 3 to 5 days. I can't wait that long.
2006 Ford Focus Signal and Tail Light Issue?
First you have to look at your taillight sockets and make sure they are not burned if they are well you need to replace it .For example if the socket is black inside you need a new one. Also if you go to any Autozone they would be more than happy to help you out with this issue . And if not well ask the Autozoner if he/she recommends anyone that does not charge that much like the dealers.
2006 Ford Focus Signal and Tail Light Issue?
sounds like a ground problem. the tail lights have a lower amp draw than the turn/ brake lights.get a jumper wire and connect between the ground wire in the circiut and a good chassis ground. if that fixes the problem find the bad ground connection

04 cadillac escalade right side tail light dont work?

why is it that my 04 cadillac escalade rear right tail light dont work......it works when i am on reverse or pushing on the brakes is just that while i am on the road driving at night it stays off while the other one(the right rear tail light) stays on..i've changed all my light buls on that bad tail light but still dont work could you please help me...
04 cadillac escalade right side tail light dont work?
Sounds like the bulb is still bad. They should be 2 filament bulbs and the tail light filament is broken.
  • msdn
  • data into xsds
  • How do I change the light switch assembly in a '95 Mustang ?

    I pull the switch and the headlights come on but no parking lights and no tail lights.No dash lights either. I checked all the fuses, and seem to think it is in the switch.
    How do I change the light switch assembly in a '95 Mustang ?
    own a 95' too. best bet,get a haynes or chilton guide ,it talks you through it.

    Why isn't my tail light working?

    I have a 2001 Nissan Altima. I change the light, but it's still not working. What's the problem?
    Why isn't my tail light working?
    Terminal is corroded, or the wiring has a short in it.
    Why isn't my tail light working?
    Check the fuse. It is in the fuse box, probably located under the dash somewhere. It could be the wire has rusted or been compromised. A current meter would easily tell you if the wires are 'hot' or not.
    or a fuse!
    Because it's broken
    Check your fuses. I recommend the Bussmann fuse checker. I picked on up at Walmart and it is a lot more convenient than taking each fuse out. Also the back of the fuse checker doubles for a thing to pull them out.

    Tail light is not working correctly?

    The passenger side brake light on my 1997 International truck stays illuminated even when I'm not pressing the brake (with the lights on). When I turn the lights off and press the brake it doesn't illuminate. Nor does the turn signal work back there but does up front. I changed the bulb but that didn't help. Any suggestions?
    Tail light is not working correctly?
    First check and make sur that the right bulb is installed in light I beleive it needs to be a 1157 bulb. If correct bulb is in place check light socket and make sure that the is no junk stuck in the white grease tha is usually in socket. If this still is a problem syart tracing the wires back to the cluster. If you need a wire diagram most Libaries that are big have a reference book that you can make copies of. And last but not least if all else falls you can go on the web to KTSA radio 550 in SAn Antonio on Sat/ Sun and ask a guy name steve gerline who has a show everyweekend and is supper good with answering questions like this

    How do i change a brake light in a 2003 nissan murano?

    and i know you have to change the bulb, i just cnt seem to get to the bults to get the tail light out. i should probably just take it to nissan hu? if you can help please let me know! thank you!
    How do i change a brake light in a 2003 nissan murano?
    Open the rear hatch and look for a removable interior panel near the taillight and remove it.The bulbs or speed nuts that hold the taillight assembly in place should be visible.Remove the bulb or the nuts holding the taillight in place and replace the bulb.
    How do i change a brake light in a 2003 nissan murano?
    The question is: How do you remove the interior panels without damaging them?

    Report Abuse

    How to change 2001 nissan maxima tail light?

    Tail light or tail light bulb? Ok to change tail light bulb remove trunk finisher that has about 2 clips and you can see the bulb holder to change tail light assembly remove 3 nuts and take the assembly out from out side of the car . I hope I helped you.
  • extension to sqltableprovider
  • hair loss treatment
  • 2009 eagle scooter 1500cc no lights. single light and tail light brake light are working?

    I change out my stator and now i have no light. If i give it gas my light are ok lets off the gas light are dim.
    2009 eagle scooter 1500cc no lights. single light and tail light brake light are working?
    if the lights get brighter an dimmer as you rev then it sounds like the battery either isn't charging/regulating properly or is worn out. Could be as simple as a new battery (autoshops can usually test a battery for free) but it could be a blown regulator or bypass resistor.

    Try the battery after that you'll probably need and autoelectrician

    Which fuse is the tail light fuse for a nissan sentra 2003?

    My tail lights and my dash board lights went out. I know there is a certain fuse that i have to change but i cant figure out which one it is from the diagram. It dosent really give names. Any one know which one it is or where on the net i can find it ? thx
    Which fuse is the tail light fuse for a nissan sentra 2003?
    I've had that exact same problem. The fuse, though I can't remember which one it is, will be under the hood in the fuse box. I would recommend getting a flash light and a pair of pliers to go through each fuse in the fuse box.



    It's annoying, because the whole short is actually a safety mechanism Nissan installed to make you aware that your tail lights are out...by making dash lights go out...not sure how safe that is at night.

    2003 chevy malibu-water in tail light- rubber issues...please read..need help?

    I am finding myself changing the bottom left bulb in my right tail light every 3 months or when it rains heavy. Obviously, water is getting into the tail light. I have taken it apart and looked, it seems to be coming through the rubber that goes around the tail light. Where would I find a replacement? Is it hard to replace it yourself? I would rather replace the whole thing that patch it b/c it's begun to be a burden to do this every other month. please help me. any advice would be okay!



    Also- I have researched this problem for almost a year now. There seems to be problems with ALL models of Malibus starting from as early as 1998 to present with this exact same issue. Why hasnt chevy issued a recall? I mean...Come ON! Hah! Can any one tell me why they haven't done this? I've already reported the issue with them, twice.....They just report it..I laugh everytime I see a Malibu on the road with the same problem.
    2003 chevy malibu-water in tail light- rubber issues...please read..need help?
    I'd second the suggestion to drill a SMALL hole in the tail light. Best practice is to remove the tail light, turn it upside down, and drill the tiny hole in the bottom of the light, making sure the water drains outside of the body of the car. If you drill it far enough inboard, it won't even be visible when the light is reinstalled. I used to have a Pontiac with this same problem. This solution worked very well for me.
    2003 chevy malibu-water in tail light- rubber issues...please read..need help?
    if the dealer wont do anything,you can always drill a little hole on the bottom of the light cover to let the water drain. i would call the head office to complain about the problem.
    If it were my car I would buy a tube of clear silicon adhesive and smear a thin bead around the rubber gasket while you have it apart. I use this adhesive for many things. It costs about $4. at the auto supply.

    How do I change the rear light bulb on a 2000 ford taurus?

    My left tail light is out on my 2000 ford taurus. How do I change it?
    How do I change the rear light bulb on a 2000 ford taurus?
    pop the trunk and u should be able to lay down the carpet or take off a little panel than twist out the bulb socket turn the bulb the bulb will come out get the new bulb twist it in put the socket back in place and then the carpet or panel back and u will be done
    How do I change the rear light bulb on a 2000 ford taurus?
    YOU GOT TO TAKE THE LAMP FROM IN SIDE THEN CHANGE IT MAKE SURE YOU HAVE THE RIGHT BULT AND DISCONNECT THE BATTERY
    You need to access the assembly from inside the trunk. You may have to remove the panel that lines the trunk in that area. Once you locate the assembly make sure you change the correct bulb because there may be more than one bulb in there.

    About the S 10 p/u, year 2000, how to remove the rear tail light lens to change bulb that is out. thank you.?

    open the tailgate and look for the screws holding the housing
    About the S 10 p/u, year 2000, how to remove the rear tail light lens to change bulb that is out. thank you.?
    If you let the tail gate down, look through where it latches. One screw will be there and the other is about 4 inches below it. Once they are out, you can pull the tail light assembly out and change the bulb.



    I have owned 2 S-10's
  • kids hair
  • programming
  • Is the tail light assembly the same on a 98 Prizm as a 98 Corolla?

    I have a 98 Prizm, which is the same as a 98 Corolla and I can't stand the look of the tail lights. I want to add some Altezza tail lights but they only offer them for the Corolla. I was curious if I could buy some Altezzas for a Corolla and put them on my Prizm.



    I know that a Prizm is not the car that you should be putting gigantic rims, a body kit, and a spoiler in... it would look ridiculous. I just hate those tail lights and want to change them, I dont plan on changing anything else.
    Is the tail light assembly the same on a 98 Prizm as a 98 Corolla?
    No, sorry it won't work!

    I have a 2001, S80, The left and right tail lights do not work, however the center brake light in the rear win

    I have changed all the light bulbs, I have checked all the fuses. all is OK. We are getting a brake failure message on the dash
    I have a 2001, S80, The left and right tail lights do not work, however the center brake light in the rear win
    That is one for a Certified mechanic to look at.
    I have a 2001, S80, The left and right tail lights do not work, however the center brake light in the rear win
    the brake lamp switch probably has a separate contact for the high mount lamp and is working while the contacts for regular brake lamps have failed. recommend test, replace switch
    We have had to replace the contacts for these,that is the metal portion of the assembley.make sure you are getting power and ground to the points first with an Ohm meter
    if the third light works there is a broken circuit between the third light and the rear of the car
    They might need to fault trace the lines,

    2004 Jeep liberty tail light problem.?

    The driver side tail lights are completely out, after changing the bulbs and checking the fuses the lights are still not working. Now the top brake light isn't working as well. (The passenger side lights are fine as well as the headlights) What could be the problem? Can I fix it? What's an estimate to get it repaired at the dealership?
    2004 Jeep liberty tail light problem.?
    Wow tough one. Do you have a trailer hitch set up and after market wiring? If so then the only other thing is a bad connection at that harness in which all the wires are usually marked on the harness so check each carefully. Also pull the light(three ten mm bolts) and turn lights on and wiggle wires at the bulb themsleves while someone is at the helm hitting the brakes and look at the bulbs during that check. I would also check the bulbs and fuses one more time because they're isnt much else. One more thing to do is call a friend or a Chrylser garage or employ the internet for a tailightwiring diagram and see what is all on the system and chase each electrical connection down. Any more questions dont hesitate to ask ill be glad to help.

    2006 magnum tail light works but right side brake light doesnt. I changed the bulb but still nothing.?

    If it is not the bulb, take it to the dealer. It is still under warranty.

    Good luck.

    How do i change a 2005 jeep Laredo tail light?

    The boot has to be opened it is held to two phillips screws and to be plugged out.
  • server
  • myspace quizzes
  • Replacing a 2001 honda civic tail light help!!!!?

    i have a 4 door honda civic we bought the part but of course it didnt come with any instructions!!!! so if you have any clue on what i need to do to change the light cover please help!!!! my car needs to get washed and i cant do it until i change that piece! please
    Replacing a 2001 honda civic tail light help!!!!?
    You may want to buy a Honda Civic Service manual from your local auto parts store; it makes a good investment.



    But typically, you should find several nuts holding your tail light from the inside of your trunk. Use a ratchet wrench and the right sized socket to remove the tail light. Disconnect the wire harness and remove your old tail light. Attach the new tail light and bolt it securely then reconnect the wire harness; make sure you have the right tail light bulb inside.



    Good luck!

    Can you buy clear or smoked tail lights for an r34 4door skyline?

    i have a 4 door r34 skyline and i would like to change from the red tail lights to clear or preferably the 'smoked' or black looking ones. i cant find ANYTHING for a 4door at all. i have heard of 4door to 2door tail light conversions and that they are very expensive. i dont really want to do any major changes to the car as i want to keep it as clean looking as possible. if you have any answers or suggestions, it would be fantastic.
    Can you buy clear or smoked tail lights for an r34 4door skyline?
    yes
    Can you buy clear or smoked tail lights for an r34 4door skyline?
    I would say at this point the best bet is to ask on a free forum like



    http://www.skylineowners.com/forum/



    i see loads of 4 door owners at meets,so i am sure one of them can point you in the right direction.



    If you have no luck let me know and i will hunt around,

    Why is my yellow tail blue damsel changing color?

    My yellow tail blue damsel is changing from a vibrant blue to a weird purple-whiteish color when i turn the aquarium lights off. I don't have moonlights so it is just dark in my aquarium and the fish freaks out and swims around crazily and changes purple- white and stays like that until I turn the lights on in the morning. Why is it doing that?
    Why is my yellow tail blue damsel changing color?
    just normal color change associated with stress





    fish's colors fade overnight (unless they are nocturnal) it's completely normal



    unless he's turning red or something i wouldn't be worried



    is the damsel fairly new? or did you recently alter the photoperiod? because of an algea bloom maybe?



    over time he should get acustomed to the new lighting regimine and stop fading colors
    Why is my yellow tail blue damsel changing color?
    damsels will change color based on moods, yes sounds strange but blue damsels are the best example, the yellow tail blue damsel is alittle different, but the blue damsel will change from bright blue to a dark purple when it is scared.
    It sounds like the results of an illness, but also consider how long you have had the Damsel as most will drop their colour as they get older.

    Help changing Taillight for 98 Ford Escort?

    I feel like an idiot because I tried to change this tail light last night in the dark and failed! There were 2 screws on the outside that I removed but I must be missing something. I was afraid of breaking the housing. Any help?
    Help changing Taillight for 98 Ford Escort?
    open hatch back,remove plastic panel you can acess tail lights here.turn bulb socket to remove.good luck
    Help changing Taillight for 98 Ford Escort?
    i think you can open the trunk on that one,,and get to the bulb from behind ,,theres a panel you remove on the inside that gives you access to the socket,,and then you change the bulb out,,if i remember right,hope im right ,,here good luck,maybe this will help.

    BMW 325i Tail Light.?

    Im about to get a 2006 BMW 325i and i noticed that the style of the tail lights arent the best and i was wondering if it would be possible to change the 325i tail lights to a 2006 BMW 525i tail lights? and if possible what would be a good estimate of the cost to exchange them?
    BMW 325i Tail Light.?
    the wont fit... you would have to change the whole rear end... that is expensive
    BMW 325i Tail Light.?
    The 325i tail lights are smaller than the 525i tail lights. You can get up graded versions though on the internet.
  • girl myspace
  • makeup green eyed beauty
  • Crown Vic / Gr Marquis Tail Light Compatibility... Is That Possible?

    Both tail light lenses on my '99 MGM were (are) broken so, I went to the junk yard %26amp; haphazardly bought 2 off of a Crown Vic. My 1999 Grand Marquis was manufactured in September, 1998 %26amp; the Crown Vic Mfg Date was October, 1998. It's quite obvious, at 1st-glance, that the physical appearance of the MGM lenses differed from that of the CV: The Crown Vic lenses are mostly red, w/ a strip of amber at the bottom (presumably the amber is the turn signal). The original MGM lenses were completely red, w/ NO amber.



    Physical differences aside, I thought that they'd [I]surely[/I] have compatible wiring %26amp; connectors. My presumptions appear incorrect(!)



    --%26gt; MY QUESTION IS: Is there ANY way (short of changing-out the Lighting Control Module) to make the CV lights work properly in my MGM?



    After performing some novice DIY rearranging, cutting/splicing of wires, I was able to get the lights to come on in various configurations but, I don't see a way to make the bottom 2 bulbs (amber) to act ONLY as a turn flasher, and the top two (red) to act ONLY as parking and/or brake lights.



    *[See wiring description(s) below, if needed]*







    CROWN VIC'

    Wires out, from connector:

    Org/Blu-stripe;

    Green;

    Blk;

    Brn.



    Wires in, to bulb connector/sockets:

    TOP 2 bulbs (behind red lens) -- Blk=Ground Bro=Minor Grn=Major

    BOTTOM 2 bulbs (behind amber lens) -- Blk=Ground NO WIRE=Minor Org/Blu-stripe=Major







    ]Grand Marquis

    Wires out, from connector:

    Org/Blu-stripe;

    Blk;

    Brn.



    Wires in, to bulb connector/sockets:

    TOP 2 bulbs (ENTIRE lens is red) -- Blk=Ground Brn=Minor Org/Blu=Major

    BOTTOM 2 bulbs (ENTIRE lens is red) -- Blk=Ground Brn=Minor *Blu=Wires Dead-End Inside Tape-Out therefore, %26quot;Major%26quot; is not powered.
    Crown Vic / Gr Marquis Tail Light Compatibility... Is That Possible?
    I don't think so. What I do with the junkies is find out whats interchangeable when I go to the front desk and they give me the interchangeability matrix. Sounds like you got a job. I also go to car-part.com for parts and I can get those sent to me. Wish you well, sorry I can't help more.
    Crown Vic / Gr Marquis Tail Light Compatibility... Is That Possible?
    if they look the same and they fit the same they the same

    Black Cat's tail changing colour... Why?

    I have a black cat with all white paws on all four, white belly, and white neck and white in the ears. She's a growing kitten, weighing about 3 pounds, very healthy, beautiful shiny coat. recently, I noticed the tip of her tail changing to a medium to light brown colour. She doesn't sleep near a radiator or anything very hot, nor cold. Her tail is changing and progressively the brown is moving further and further down the tail.



    Why is her tail changing colour?
    Black Cat's tail changing colour... Why?
    Because its getting close to summer

    this is happening to my tortiesheel she's turningmore ginger
    Black Cat's tail changing colour... Why?
    I'm guessing she's probably just getting some of her adult fur growing in on her tail, which could cause the slight color change. If she has some sort of simaese/pointed cat influence, her %26quot;ends%26quot; might adjust color too due to temperature, but usually they turn darker, not lighter.



    If she seems healthy and happy otherwise, and the coat seems healthy, it's probably not a sign of anything negative.



    Weird!
    is she going out in the sun? ive a black and white cat that seems more brown and cream in summer
    male pattern browning
    I have a dog that was all black as a puppy except for one white patch on his chest. When he got older (he's like 3 years now) He got silvery patches behind his ears, and his white patch got bigger, and he is more of a dark brown color all over.



    I think it just happens with some animals when they get their adult fur.

    Sunlight can also do that I think. All of my black cats go brown in the summer.



    It's probably not something you should worry about too much, as long as she's healthy.
    Just like us - kittens change during their kitten (baby) and young adult (teenage) years - A cat is considered a young adult up to 2 years - It is nothing to be concerned about - It is possible she is considered a 'calico' cat and the tan/brown is just now showing up in her coat -



    I have a cat that when he was born was white - at 4 weeks his fur turned to a very pale silver gray - at about 2-4 months his tail and ears started darkening - by one year he had all the markings of a siamese - at 2 years he stopped changing - I show people pictures and they all swear it is not the same cat but I know it is because I fostered him and his siblings when his mama got killed by a car - there were 6 kittens total 3 male/3 female - 3 long hair/3 short hair - 2 black and white - 2 orange marmalade - 2 gray (blue) siamese -

    Will my tail light pass ?- Vehicule inspection - Ontario?

    I've just moved from Nova Scotia to Ontario and I am now proceeding to my plate changes - Like in NS i do have to proceed to a vehicule inspection but here's my worry:



    One of my rear tail light is slightly broken - Although there is no visible %26quot;white%26quot; light, when i got inspected in NS the matter was taken care of my the garagist who simply put a bit of red tape on it. It really isnt a big thing - but i can't afford changing a whole light cap right now.



    Will this cause a problem with my Ontario inspection ?
    Will my tail light pass ?- Vehicule inspection - Ontario?
    That red tape is meant for a temporary patch, it doesn't replace a lens, and it doesn't allow as much light to come through. It may pass, but it shouldn't, and it shouldn't have passed in Nova Scotia either. Don't be so cheap. Go to a U-Pick yard and buy a used lens, it will be a lot less than a new one. If you can't afford a lens, how can you afford to own a car? How could you afford to move? How can you afford gas? As an insurance broker, I don't have a lot of empathy for people that don't properly repair safety items.
    Will my tail light pass ?- Vehicule inspection - Ontario?
    I wouldn't think so, since there's no white light showing. But I'm not for sure.
    HIS QUESTION IS ABOUT CANADA AND NOT THE UNITED STATES SO THANKS FOR THE INFORMATION THAT WAS NOT ASKED FOR UCANTCME
    IN THE U.S. ANY CRACKED LENS THAT TAPE IS USED ON WILL NOT PASS INSPECTION, I WOULD SUGGEST THAT YOU CONTACT YOUR LOCAL DMV OFFICE, THEY WILL BE ABLE TO ANSWER ANY AND ALL OF YOUR QUESTIONS AND AT THE SAME TIME YOU WILL BE GETTING THE CORRECT ANSWER TO YOUR QUESTION.

    Right tail-light issues: sometimes works and sometimes not?

    My son's '93 Neon' right tail light works on and off. The left one has no problem. He has changed the fuse, checked the light itself. He was told it is probably electrical. Any suggestions on how and where to start checking? It seems obvious its something directly attached to that rear light. Signal and backup works on and off also. I think it's a loose wire, but have no idea where to look. Someone mentioned Dielictic Grease on another tail-light Q. Where is that found and would it affect only one light? Where is the Harness connector found? Thanks in advance.
    Right tail-light issues: sometimes works and sometimes not?
    I would check the ground wires, if that does not help then it may need a diagnostic check
    Right tail-light issues: sometimes works and sometimes not?
    First check the bulb, the filament sometimes will make contact as the car wiggles. Second check the light bulbs connector for rusted or warn contacts. Open the trunk to access the rear lenses.
    Yup...ground wire to the body.

    Right tail-light issues: sometimes works and sometimes not?

    My son's '93 Neon' right tail light works on and off. The left one has no problem. He has changed the fuse, checked the light itself. He was told it is probably electrical. Any suggestions on how and where to start checking? It seems obvious its something directly attached to that rear light. Signal and backup works on and off also. I think it's a loose wire, but have no idea where to look. Someone mentioned Dielictic Grease on another tail-light Q. Where is that found and would it affect only one light? Where is the Harness connector found? Thanks in advance.
    Right tail-light issues: sometimes works and sometimes not?
    It sounds to me like the right side has a grounding problem. Check to make sure which wire is the power (+) wire and trace the other wire if you can. This same wire goes to all the lights to complete the circuit. That would be the ground (-). If you can't trace it you can try putting a temporary jumper wire from it to a good metal area for a ground. Make sure it is not the power wire or you will blow a fuse and maybe cause more damage!!! Cars are grounded through the body so if it keeps working after that you know what the problem is. Then you just have fix the ground problem. It seems like it may be a bad wire in the wiring harness between the two sides. Good luck and Merry Christmas!!
    Right tail-light issues: sometimes works and sometimes not?
    Put a bulb in it even if it %26quot;looks%26quot; good.
  • cemetery plot
  • client time
  • 2001 chevy cavalier tail light problem?

    i have a 2001 chevy cavalier...when i signal the right blinker, the dash shows the arrow blinking rapidly, telling me my bulb is out on my rear tail light...so after i changed it, it worked for awhile then started blinking fast again...im thinking its a wiring problem or maybe the lube thats in the area where the bulb goes...any suggestions, and if so can i do it myself?
    2001 chevy cavalier tail light problem?
    Certain year Cavaliers have silent recalls on rear tail light sockets. It most likely is a bad socket.
    2001 chevy cavalier tail light problem?
    You may just have a bad flasher. They are inexpensive and easy to replace. They are usually located on the fuse block on the drivers side under the dashboard. Just unplug the old one and plug in the new one. There are usually 2 of them. One runs the turn signals and the other runs the emergency flashers. If you want, you can switch them to see if that's what the problem is.



    Hope this helps and good luck
    you have the typ of bulb socket that requiers a complete seal around the lennes area so make sur the seal is tight to keep out mostcher an dust drit , make shure all wires are thight and weather proff also
    change the flasher before getting into the wiring.

    Please help me with my 1994 BMW 525i Tail light problem?

    Tail lights and 1 brake light out on 1994 BMW 525i. Bulbs and fuse appear to be good.I changed the bulbs anyway but it did not work.A friend says to clean the bulb holder and make sure the grounding tabs are making contact. Im not sure what he means. I never had this problem until now can someone help me?
    Please help me with my 1994 BMW 525i Tail light problem?
    I assume you mean the brake lights. I had to play with a customer's car that had similar problems. Was the brake switch under the dash. Even if you could get to it. I had done the pdeal alot, and then it had started to work fine. But I'm sure it was only a temp fix. Possibly need the switch replaced. Is only a dealer item too. Good luck.
    Please help me with my 1994 BMW 525i Tail light problem?
    its the place where the bulbs go in,,they may be corroded ,,and not making good contact,,that will make them do this,,if all the fuses and bulbs are good it has to be a bad ground or broken wire in the rear of the wiring harness,,if you,ll take your time you might find it,if not you may need to take it in,,and get it checked out,,you might cause more damage than you can repair if your not real familiar with wiring,,i own a repair shop,,in Tennessee and we specialize in electrical ,,i hope this help,s,,good luck with it.
    ha ha ha ha ha ha ha ha ha sounds like my 200 dollar chevy beretta

    How much does it cost to change regular tail-lights on your car to all white ones?

    illegal in most states if they dont turn red when they are on

    My tail light on the passenger side goes out whenever i hit the breaks and turn on the turn signal?

    On my 1999 dodge dakota when i hit my breaks i have break lights but when i go to turn my turn signal on it cuts off? I have already changed all the bulbs and the wiring harness and taken everything out and used bulb grease dielectric grease any ideas?
    My tail light on the passenger side goes out whenever i hit the breaks and turn on the turn signal?
    Faulty earth on the light unit.

    How do you change the left rear tail light on a 2004 acura tl?

    on the inside of the trunk you can get to the tail light.
    How do you change the left rear tail light on a 2004 acura tl?
    Look inside the trunk behind some padding or some hardboard material. Half turn on the socket should remove it.
    How do you change the left rear tail light on a 2004 acura tl?
    If you are talking about the actual taillight you need to remove the rear bumper and find remove the bolts holding it at the bottom.
  • cat
  • ie hosted control
  • How do I get to my dash light?

    I have a 98' Saturn SC2, my fog lights, tail lights and dash lights were all out, so I changed the fuse and they all work but my dash lights. So I was wondering how do I get in there to change the light so that my car will pass the safety inspection?
    How do I get to my dash light?
    Check for another blown fuse.

    How do you change the bulb on an '04 Jetta tail light?

    Remove the carpeted piece right behind the tail light, you cant see it you have to look for it. But get your fingers in between the crack and pull on it. It is just being held on by velcro. It is easy trust me. Then you take the liitle light bulb out and replace it.

    I can't figure out how to change my 2007 ford focus tail light bulb.?

    yes i know there is one srew and clip, but i cant figure out how to get the clip undone. any help would be greatly appreciated.
    I can't figure out how to change my 2007 ford focus tail light bulb.?
    i have an 05 the same problem you have to pull the clip loose with out breaking it ive change mine 3 times without it breaking

    Does anyone know a way I can get my trunk open so i can change my tail lights?

    the lock to my trunk is messed up and i cant figure out y my trunk realse wont work. any ideals on how to get in the trunk with minmum damage.
    Does anyone know a way I can get my trunk open so i can change my tail lights?
    Need the Year, Brand, and model of your car... 91 Chevy Caprice



    Emailed already...

    Drill out the broken lock that your key turns...

    make sure you don't damage trunk lid

    Once you remove the key lock you will notice a rod that goes from the key lock to the truck latch.

    Use a long (small tipped) flat head screw driver to turn the latch lock.

    You will be able to open and close trunk now

    You will also be able to replace the lock cylinder once you have the trunk open...



    Happy motoring...
    Does anyone know a way I can get my trunk open so i can change my tail lights?
    This might sound old school, but try sticking a credit card in the lock lever. It could push the locking mechanism up.



    Or, try shorting out the electronic lever by pulling the fuse out and putting it back in rapidly.
    in some cars you can pull the back off of the back seat to get into the trunk,them just flip the latch on the truck lock
    Maybe remove back seat.
    Fix the lock first.

    Depending on the vehicle the light assembly can be removed and the bulbs then replaced, all outside.
    take it to a body shop so even though the shop ppl damage it they have to fix it for ya
    Get real close to the outside of the trunk lid and yell REAL loud at the guy locked in there to open the lid from the inside.



    Works like a charm.

    Jeep Cherokee driver side parking light, and rear tail light went out. Changed bulbs, and it didnt fix it!?

    both lights went out at the same time, I changed the bulbs and they still dont work.. Is there a fuse that could be causing this?
    Jeep Cherokee driver side parking light, and rear tail light went out. Changed bulbs, and it didnt fix it!?
    Possibly a broken ground wire. A fuse is not set to each side of the vehicle but the system it is tied to. Had a bad ground on my truck ( I broke installing hitch ) and it caused plate light to die and rear turn signals to not work. Just fixed that and lights worked great
    Jeep Cherokee driver side parking light, and rear tail light went out. Changed bulbs, and it didnt fix it!?
    yes, check the fuse box either under the hood, or under the dash board
    Sounds like a fuse went out or a wire has a short. Check your fuse box. Once you find it (usually in the most inconvenient place possible), pull a fuse at a time. If the wire is solid all the way across, it's a good fuse. If there is a gap, the fuse is blown and you need a new one.
    If you don't have an owner's manual, you can download one online. The manual will list the location of all the fuses.
    Jeep running lights are all on the same fuse, so if the fuse was dead they would all be dead.



    However you didn't mention the year. Jeeps before 1998 or so all have bulbs which have the nasty %26quot;bulb grease%26quot; on them. Did you get any of that into the socket? Also twist-lock sockets are a pain to get the bulbs seated in correctly. Try seating it (again) if you found a burnt out bulb.
  • strange characters during boot up
  • fish
  • How do I change the break light on a nissan 2001 sentra?

    my left back tail light went out I got the correct light bulb for it but can't find the way to replace it help with some detailed steps if you can don't want to take to shop just to change a light bulb.
    How do I change the break light on a nissan 2001 sentra?
    nissans are fairly simple just got to the trunk look and you should see some plastic plugs. remove those and remove the nuts that are holding the tail light and replace. if not this steps, then just remove the cover and replace the bulb from the inside the trunk brehind the light

    How do toy change the break light on a nissan 2001 sentra?

    my left back tail light went out I got the correct light bulb for it but can't find the way to replace it help with some detailed steps if you can don't want to take to shop just to change a light bulb.
    How do toy change the break light on a nissan 2001 sentra?
    Look in the trunk on some cars you change from inside the trunk by pulling out the socket. Hope it helps good luck.

    How do you change the tail lights in a 2000 Ford Mustang? Cant find the owners manual.?

    try this..

    http://www.youtube.com/watch?v=Otuww3Ub9鈥?/a>
    How do you change the tail lights in a 2000 Ford Mustang? Cant find the owners manual.?
    open the trunk and pop out the liner. Should be 4 plastic %26quot;bolts%26quot;(look like trees) by your trunk latch and then there should be 2 plastic screws 1 on each side right behind the taillight. Once you have those out the liner should come out. Then once you have that out there should be 4 bolts holding the taillights in.

    Why did my tail lights go out on a 1993 Corolla?

    The right tail lights went out. People told us our brake lights did not work when we braked (right only).

    So, I changed bulbs in right tail lights (there's 4).

    Two of the four are the same part number (the two tail light bulbs).

    The other two are a different part # (one for backup light, one for turn signal).

    During my changing of bulbs and investigating whether the bulbs were indeed blown, I realized the bulbs were ok.

    So, I got into the fuse box under the hood. Although Toyota has a diagram of which fuse goes to which electrical thing, e.g. headlights, AC, heater, etc. There is no mention of tail lights on the box or in owner's manual.

    So, I'm screwing around and taking out fuses, trying to find which fuse (or relay) controls the tail lights. I take out a small fuse (7.5A); It's blown, I replace it with a spare 7.5A.

    What it all boils down to is this: I have no tail lights, both right and left. I do have the reverse lights and left brake light. Did I screw up something?
    Why did my tail lights go out on a 1993 Corolla?
    you have an electrical problem. find the source.



    could be a chewed up wire..water somewhere...blown bulbs..blown fuse..damaged wiring
    Why did my tail lights go out on a 1993 Corolla?
    Because your car is really old.
    you sure did...you got the henway out of calibration....
    you might have screwed something up but some of the wires could of burned together
    check if the parking lights in the front work. if they do that eliminates the parking light fuse (which would be the fuse that has the taillights)



    Get under the car and check wiring.



    If you didnt replace the bulbs after they looked OK, replace them anyways for the heck of it
    buy a new car
    i own a repair shop and i have had this happen to me before,look on the left or right tail light on the inside of it,in the trunk area and see if one of the taillight has a small relay box on it ,i ran across this a while back and that relay had burnt out,Toyota and Nissan actually had a relay for the tail lights,and mine had burnt out,it only cost a few bucks to replace but it drove me nuts finding it,you can take a 12 volt tester and test the wires right up to the relay,this is how i found mine bad,and when it went out ,it went all the sudden just like a fuse had blown,but look on both tail lights to see if yours has one,those things will drive you crazy trying to find out whats making the lights not work,good luck with it i hope this helps.

    Can you change the back tail lights to a car?

    I have a mitsubishi galant (1994) and I think the back lights are really ugly.

    Is there any way I can take the entire back light strip off and put on two separate ones on each side?

    Thanks
    Can you change the back tail lights to a car?
    Try Summitt Racing
    Can you change the back tail lights to a car?
    Yea just use a search engine and find somewhere that sells alternate tail lights for a mitsubishi galant. You can find really cool ones on slickcar.com. Installation might be a little difficult if you do not know what you are doing.
  • cat
  • listview bug
  • How do i change the tail lights (NOT THE BULB (10 pts)?

    I plan on changing the whole tail lights on my cavalier.

    Something like this --http://www.andysautosport.com/chevrolet/鈥?/a>
    How do i change the tail lights (NOT THE BULB (10 pts)?
    inside the trunk there will be 2-6 nuts or wing nuts

    that secure the light housing to the body



    many newer body styles require the light removal

    to change bulbs anyway



    with light removed give light bulb socket a quarter

    turn to remove

    reverse procedure for installation of new light bucket
    How do i change the tail lights (NOT THE BULB (10 pts)?
    Well open the trunk pull back the cover around the lights and unscrew the screws take out the bulbs and install in reverse.
    MOST HAVE PUSHPINS OR SCREWS OF SOME SORT.. TAKE THEM OFF AND THE HOLE LIGHT SHOULD COME OUT.. EASY

    Is it possible to change the tail lights on my 2008 Mercedes s550 to the 2010 taillights?

    Are they the same size?
    Is it possible to change the tail lights on my 2008 Mercedes s550 to the 2010 taillights?
    Yes they are the same size and yes it is possible. Actually, someone on MBWorld (http://www.mbworld.org/) has managed to do it. Here is the link to the thread (http://www.mbworld.org/forums/new-s-clas鈥?/a> Look for posts by CL55 Serge, he is the one who has actually, and successfully, done it. Personally, I would have your dealer do the install, but if not, I would highly recommend MBenzNL (http://mbenznl.nl/), they do fantastic work. Good luck.

    How to change the tail light bulb on a 2007 chevy silverado w/utility bed?

    I need an image of the assembly if possible. I have already tried the checy website. It is not the same as a regular bed.
    How to change the tail light bulb on a 2007 chevy silverado w/utility bed?
    Different lights on different beds. Is this a sealed unit light assembly mounted in a rubber grommet like on an 18 wheeler trailer? I have seen

    some of the new light assembly's that are the LED assembly's that

    have a metal ring riveted to the body to stop theft.

    How do you get the tail light lens off an 03' town and country to change the bulb???

    If it is anything like my 2000 Grand Caravan, you open the rear liftgate and look at the taillight assembly. There should be two phillips head screws. Remove those and rotate the lens out and away from the inside of the van. Be careful not to snap the tab off the opposite side of the lense.
    How do you get the tail light lens off an 03' town and country to change the bulb???
    Look inside. Most now change without any tools needed.

    Tuesday, September 20, 2011

    How do i change the tail lights on my scion tc?

    i just got some tail lights on ebay %26amp; i thought i could change them myself. so far ive taken out the bolts but they still wont come out
    How do i change the tail lights on my scion tc?
    You need to remove the bumper,

    http://www.scionlife.com/forums/viewtopi鈥?/a>
    How do i change the tail lights on my scion tc?
    Very carefully...
    Yeah you have to remove the bumper, it really is a *****. I would recommend taking it to a body shop, that's what I had to do to put mine in.
  • parameter
  • lock file
  • "Why do the tail lights remain on if the car and lights are off?"?

    its on a 91 totota corolla, also the blinkers dont flash, they still make the blinking sound though.this all happened after the guy at autozone changed my tail light bulb.
    %26quot;Why do the tail lights remain on if the car and lights are off?%26quot;?
    he probole installed the wrong kind of bulb.
    %26quot;Why do the tail lights remain on if the car and lights are off?%26quot;?
    Take it back to auto zone and let them figure it out.
    there is a brake switch at the brake pedal. it could be be broke and might need replacing
    If a wrong bulb is installed, it could put everything else on the fritz. Autozone guys are there to help you pick the part you need, not install it, thats why they don't work at a shop. Ask them too look up the tailight number needed and compare it to the one that was replaced. Also, this may not pertain to your car but old import vehicles are notorious for lighting electrical issues called %26quot;return to ground%26quot; meaning multiple circuits have failed and are allowing current to go through.
    check all of your fuses... your manual should indicate where to find them.



    remove the fuse from its position and observe it... if the metal link (you can see this if you look at the side of the fuse) is still connected and disconnected, the fuse is ok... if the metal is %26quot;blown%26quot; or broken in half... the fuse needs to be replaced... i'd give that a look.. doesn't take much time.



    (btw.. there should be a fuse-remover tool in one of the fuse+relay boxes under your hood... use that to remove the fuses.. it makes life a lot easier...)

    How to change oil in a 96 jeep grand cherokee and how to replace a rear tail light as well.?

    Just wondering how easy it is to access both of these different things.
    How to change oil in a 96 jeep grand cherokee and how to replace a rear tail light as well.?
    no sweat real easy. oil drain plug is on the bottom of oil pan. you will need to slide underneath to get at it. oil filter is on the side of the block, get that while you're down there. rear light, get at them from the inside rear panel. nothin to it. go fo it.
    How to change oil in a 96 jeep grand cherokee and how to replace a rear tail light as well.?
    the tail light you can access by opening your trunk (lift gate) and looking at the lens there should be some Philips (+) head screws. after you remove them the lens assembly will come right off you van then twist the bulb holders and remove the bulbs. the oil change part of your question you should probably have a friend walk you through this process. if you don't do it right you could really screw something up.
    It's easier said than done, simply get in your Jeep, start it up and drive it over to your local mechanics garage and pay him to change the oil and replace the bulb.



    Then you can run around and tell your friends you just changed your oil and replaced the light for under $30.00 and the best part about it was you never even got dirty doing it.



    Remember this: If you take your car to like any shop and they forget to tighten the drain plug and after you leave and you're driving down the street the oil leaks out and the engine locks up. Guess who's paying for the repairs? Not you, but that shop is.





    Good Luck

    Why is my tail light not working?

    My brake light works yet the tail doesn't. Its the same bulb. Ive changed the bulb yet its still the same problem. Any ideas.
    Why is my tail light not working?
    Fuse? the two filaments (stop %26amp; tail) are separately fused.
    Why is my tail light not working?
    Hello



    If the one the other side is working change them over.

    If the problem remains you know the bulb is OK

    Check hand book to see which fuse covers the Tail light for the side that is not working, It will cover other things in the car, If they are working the fuse is OK

    It only leaves the feed wire to the bulb or the bulb holder or the earth from that bulb. Check each,

    If the problem changes sides then you have been unlucky and the new bulb was also faulty.



    Andy C
    First have you replaced the bulb with a two element bulb?

    Second have you checked the fuse for the lights?

    Last does the light work on the other side of the car? If it does and you have done all the other checks then the thing to do is pull the connectors for the lights off and make sure they are clean and tight.

    Ja.
    its possibly not the bulb itself.. it might be an electrical issue. either take it to a dealership, or to a shop that can figure out what's going on with it
    on the board that you plug the bulb into,it will have and connector...look inside it for corrosion...its a common fault,the earth terminal looses it contact and stuff can stop working,it can also make the brake light flash with the indicator.
    You could swap the new bulb over to the other lamp to check if the bulb is ok?and vice versa.Its unlikely to be a fuse as they usually work more than one lamp?If the bulb lights ok on the other side, then its likely to be a bad connection somewhere.Hope this helps
    First check the fuse. Then look on the bulb on the silver part Make sure you are using a 1156 Bulb. it is the one with two elements one For stop and one for tail light.
    had the same problem a few weeks ago,asked shop for a tail light bulb still didnt work(oops wrong bulb it needed the one with 2 filaments) now sorted
    bad or corroded connection at tail light plug in or possibly a bad ground or a broken or loose wire
    Did you get the bulb with the 2 elements?one for the break and the other for the tail light. :-)
    it might be the bulb socket.
    check the fuse

    Is there any meaning to 18 wheeler tail light configuration?

    I notice they change the pattern of the lights on their trailers. Was wondering if there was any significance.
    Is there any meaning to 18 wheeler tail light configuration?
    There is a meaning to some of the lights. A truck is required by federal DOT law to have left and right tail lights, turn signals and brake lights. It is also required to have 3 clearance marker lights in the center, either at the top of the back of the truck or on the same plane as the tail lights. All of which are to be red, except separate turn signals can be amber. No other lights are allowed to be on the same plane as the tail lights or clearance lights. This identifies the vehicle as a truck from the rear as prescribed by Federal DOT regulations.



    Any other lights on the back, just mean the truck owner thinks it looks cool and usually has more money than he knows what to do with.



    On the sides of the trailer, it is required by federal DOT regulations to have 1 amber clearance light on each front corner. On a van it is to be at the top. On a flat bed on the front corner. 1 amber light half way of the trailer(at the bottom of the side. 1 red clearance light at each back corner at the bottom. The rest of the lights with the exception of side turn signals are just to look cool and waste money.



    The extra lights are called chicken lights as are all the extra lights on the cab of the truck.
    Is there any meaning to 18 wheeler tail light configuration?
    No, as long as they have left and right signals and a brake light on each side they are legal, lot's of trucks and trailers have extra lights just for show or increased visibility.
    Actually it does have some meaning. D.O.T. has a lot to do with the way certain lights are placed on a trailer, some guys add more for fun.

    Honda civic tail light swap help!!!?

    i have a 1997 honda civic 2dr and i changed the tail lights to a 99-00 ones. the red and white ones. but the problem is that when i turn on my blinkers, they are white instead of amber. do they sell amber bulbs for 97 civic coupes???
    Honda civic tail light swap help!!!?
    take the clear bulb in, and have a parts store match the bulb in an amber color. most bulbs are universal, believe it or not
  • msdn
  • ittwit
  • How do you replace a tail light (brake) bulb on a 2004 Jeep Grand Cherokee?

    I opened the liftgate and removed the two phillips head screws from the side of the housing, however I can't move the light casing to get in and change the bulb.
    How do you replace a tail light (brake) bulb on a 2004 Jeep Grand Cherokee?
    You will most likely not find an interior access to the lights ,,, you must remove the screws on the outside and remove the casing to get to the bulbs ... Most yrs did not have any way of gaining access from the inside ... i'm not sure if the owners manual shows this feature but it would be great to have a shop manual or at the very least a Haynes or Chiltons manual for reference... Good Luck
    How do you replace a tail light (brake) bulb on a 2004 Jeep Grand Cherokee?
    Look for two more screws somewhere outside the vehicle. Also look for an access pannel just inside the back at the same level of the taillights. If there is one, you may be able to reach in and change the bulbs right there.
    After obtaining the correct light bulb-- an auto store or the dealership can tell you-- open the back hatch. On the inside back wall is where you will find access to the bulbs. I don't know if you take the interior wall off or a open a door, but try gently (It's easy to mark things up if you use a screwdriver to pry it off). You may even have to unscrew this. Make sure you put the burnt out bulb away from you in the garbage--don't want to accidentally reinstall that. Plug in the new one. And reseal the compartment. Then make sure you get behind the wheel and press on the brakes with the jeep running and a friend posted at the back to notify you if its the right light bulb you replaced--and not a night driving one..

    How hard would it be to change tail lights on a 96 s10?

    wondering if it would be easy to swap out the stock tail lights for some aftermarket ones.
    How hard would it be to change tail lights on a 96 s10?
    Pretty much the easiest thing you could think of.
    How hard would it be to change tail lights on a 96 s10?
    Open the tailgate and there are two screws. Remove the screws and carefully remove the assembly.
    Not hard at all. Take the screws out and carefully remove the assembly. And replace the new one as you took the old one out.

    Fixing a tail light on a Mitshubishi Eclispse?

    I guess I need to be alittle more direct since I am probably addressing a general men population with this question. Can I an HOW do I change a talil light on a 2004 Mitshi Eclispe? If I had general tools can it be done and HOW. Thanks again
    Fixing a tail light on a Mitshubishi Eclispse?
    open trunk.. remove plastic cover that is near the tail light... twist out the bulb socket from the tail light... and then twist or remove the bulb... .. if you want to remove the whole tail light assembly.. you have to remove the plastic trim in the trunk area.. thne you will need to remove the tail light u will need a wrench.. most likely 10mm

    My 99 silverados tail light don't seem to work only when the break is pressed. can it be the wires?

    i had the hole light changed and i don't know if the electricians did something wrong with the wires. it only works when the break is pressed but when i turn them on, its the only one that don't come on. any suggestions.
    My 99 silverados tail light don't seem to work only when the break is pressed. can it be the wires?
    You have two circuits running here. One for the running lights (tail lights) and one for the brake lights. I bet they crossed the wires between the two circuits. I have seen the lamp improperly inserted into the socket cause this to happen, as well. There might be a bad socket, or break in the wire where the tail light feed goes to that bulb. That would cause a grounding problem making the brake light filament the only path to ground for the tail light.



    Do the turn signals, and emergency flashers all work okay?
    My 99 silverados tail light don't seem to work only when the break is pressed. can it be the wires?
    It could possibly be the headlight switch, has the switch ever been replaced?
    you have two sets of bulbs on both sides one for running lights other for brakes.

    How to change a tail light on a 1990 chevy Caviler?

    Hey YA. I just got pulled over for having my tail lights out on my 1990 chevy caviler. Well I went to NAPA and got the bulbs but I am not 100 percent sure how to get them in. Any advice would be helpful. Nothing stupid like %26quot;have your dad help you%26quot; or any of that ****.



    Thanks guys and gals! :D 10pts for whoever can help me get them in! :D
    How to change a tail light on a 1990 chevy Caviler?
    There are 3 or 4 studs going through the panel where the tail lights are mounted that hold them in place, usually secured with big plastic wing-nuts. You may have to move some carpeting or a plastic panel out of the way to get that far.

    http://repairguide.autozone.com/znetrgs/鈥?/a>



    %26quot;Depending upon vehicle application, remove the lamp socket either by rotating it counterclockwise (approximately 1 / 4 turn) until the plastic tabs disengage, or by squeezing the metal tangs while pulling the socket from the light assembly.



    Remove the bulb from the socket using the appropriate method. Bulbs with blade-type bases pull straight out, while those with round bases and protruding pins (bayonet-type bulbs) must be depressed, then rotated counterclockwise (approximately 1 / 8 turn) before pulling out.%26quot;



    I'm thinking that on your model year, for a turn signal/brake bulb, to remove the socket would be the first method of the 2, and to remove the bulb would be the latter of the 2 methods.



    Re; Additional Details



    First, put some good tough gloves on, so you don't jab yourself. Then take a pointy-tipped needle-nosed pliers, jam it into the bottom and push it down in, and twist counterclockwise. Holding the pliers so that the tips are spreading out can help too. If worse comes to worse, go to the auto parts store and look in the %26quot;HELP!%26quot; section for a new socket.
    How to change a tail light on a 1990 chevy Caviler?
    You'll have to open the trunk to gain access. I would do both of them while I was at it because it seems like when one goes out, the other goes out one month later.
    open your trunk, you may have to move the carpet directly behind the lights. there should be four screws sticking out. unscrew all of them and carefully pull out the lens and housing. the bulbs should pull straight out, but you may have to wiggle them a bit. when you go to replace the lenses, be very careful not to overtighten the screws because you can damage the rubber seals.
    Open the trunk.On the back panel,maybe behind the carpet trim.You'll see some black wing nuts.Remove those wing nuts and pull out the whole tail light assembly.Once you have it out you'll see where the wires go to.Twist and pull out to remove bulb.
  • how to put numbers on keys
  • Can you quilt a queen on a regular machine
  • I have tail light but no brake or turn signal lights 1998 dodge cummings?

    I do have tail lights but no brake or turn signal lights on the truck changed flasher fuse and checked all fuses they are good. tow package wires ar good and no corrosion or brakes or shorts have checked them out and have checked all light bulbs. Thanks
    I have tail light but no brake or turn signal lights 1998 dodge cummings?
    Take the connector out of your %26quot;T%26quot; Connector for your tail lights on both sides. Check to see that you have running lights (Voltage) and turn signals (Voltage that changes up/down) and use the truck as ground or a know good ground. Some people think that the white wire is ground and in fact it is for backup lights. If your voltages are present like they should be then connect the T connector to it and check the output to the trailer and see if they work and before you connect the tail lights back into the connector check the contacts for voltage like you did when you had the %26quot;T%26quot; connector out. IF you have the voltages then it should work unless you have open bulbs or your wires are cut someplace, or worse yet the wires are grounded some place that they shouldn't be... Basically disconnect everything check the main input to the connector, check the connector, and check the output of the connector. If you ar running LED's then switch wires on the hot and ground sides. LED's only work in one direction, where a bulb will work forward or reversed wired.
    I have tail light but no brake or turn signal lights 1998 dodge cummings?
    Change your blinker fluid.

    I have a 1996 pontiac grand am -I have no turn signal, dashboard light, brake light, or tail lights?

    I tried changing the fuse. The only fuse that was blown was the hazard light fuse..when I replaced, it caused the signal lights to work but it keeps popping (blowing out). I tried checking the engine fuse box to see if the lighting fuse needs to be changed but I couldn't get those fuses to come out. Does anyone know what I can do?
    I have a 1996 pontiac grand am -I have no turn signal, dashboard light, brake light, or tail lights?
    This is all related to a failure in the multifunction switch (also known as the turn signal switch).

    When these fail,you will loose all the lights that you say.
    I have a 1996 pontiac grand am -I have no turn signal, dashboard light, brake light, or tail lights?
    unless you're great with electrical problems, i would suggest you taking it in to get diagnosed by a professional. plain and simple, you have a short in the system which is causing too much amperage to flow into that specific fuse which is causing it to blow. and whatever is shorting that out is probably taking power away from all your exterior lights. so unless you're up for a month's worth of headache, take it in :)
    you have a short in that system causing that fuse to blow. you need to find the problem, fix it, then replace the fuse
    make sure your using the right amperage fuse for ur lights

    I have an '94 lexus ls 400 how do you change the tail light and break bulbs?[just bought IT today]?

    http://us.lexusownersclub.com/forums/ind鈥?/a>

    How do you change a nissain morrano's tail light?

    please help me asap tahnks and have a nice day
    How do you change a nissain morrano's tail light?
    Open the hatch Remove the black plastic strip outside of the back door weatherstrip now you see two 10mm screws remove them the whole tail light assembly needs to be pulled rearward there are two pawn shaped snaps on the assembly that snap onto the body work. So do not pry outward it will break the pawn shaped snaps (experenced that) I use plastic pry bar set but sometime the assembly will pop out with just a good grip and rear pull. Then you can access each bulb holder Tail light brake light bulb has two filiments. snap assembly in foward rescrew the (2) 10mm and replace the black plastic cover And close the hatch
    How do you change a nissain morrano's tail light?
    I did this and the instructions are correct. The thing to do to avoid breaking the gray snaps that hold the light is ti jimmy the light enough that you can slide a flat head screw driver between the light and body and then jimmy the gray snap prong loose on top and then the same thing on the bottom

    Report Abuse


    Greg H must be one of the biggest idiots ever!!!

    Report Abuse


    I've never had a Nissan Murano, but the procedure for changing a tail-light is pretty much the same for any car.



    The lights are accessed from inside the trunk. You will probably have to fold back the carpeting on the inside of the trunk to get to the lights. Once you locate the light that is burned out, just give the socket a twist and pull it out from the fixture. Then you can remove the bulb, replace it with a new one, and put the socket back into the light fixture.



    To get the correct replacement bulb, go to an auto parts store. Be sure you know the model and year of your car and exactly which bulb you are replacing. You could even take the burned out bulb to the store with you.

    I want to change my rear tail light for a after market light ,how do i unplug the socket ,do the inside panel?

    how do i get at the plug to get the whole light out
    I want to change my rear tail light for a after market light ,how do i unplug the socket ,do the inside panel?
    well i have a honda civic, and when i changed my light i had to go into the trunk, pull the carpet away from the back, and the lights should be tucked in back there. depends on your car tho, do you still have the owners manual? if so, check that. :)
  • parameter
  • blackhead eraser
  • How to change BMW 325 tail light bulb?

    Check for thumb screws just inside the trunk behind the tail light.Take the screws loose and pull on the light assembly to get to the bulbs.

    How to change the tail light on a 1996 dodge ram 1500?

    on my 2000 it has 4 turk scews holding it in let down the end gate and see if there is some there on the corner its not hard just look and take your time ounces you have the lens off you just turn the plug in and replace build
    How to change the tail light on a 1996 dodge ram 1500?
    Open the tailgate, see two screws just inside the opening in line with the light. Remove the screws, pull straight back on the light.

    How do i change a tail light on a lexus gs 400?

    Not so hard. Open the trunk. Remove the two covers. Take off a few 10mm bolts, disconnect the electrical connector, push in the little thing to pop out the assembly, and then you can access the bulbs.
    How do i change a tail light on a lexus gs 400?
    very hard

    How do you change a 2006 ford freestyle tail light/brake light?

    The directiona , complete with diagrams are on page 59-60 of your owners guide.

    ___Copy___

    Replacing stop/tail/turn/backup bulbs

    The stop, tail, turn and backup lamp bulbs are located in the tail lamp

    assembly. Follow the same steps to replace either bulb.

    1. Make sure the headlamp switch is

    in the OFF position and open the

    liftgate.

    2. Remove the two screws in the

    liftgate opening, then pull the lamp

    assembly away from the vehicle.

    3. Remove the bulb socket by

    rotating it counterclockwise, then

    pulling it out of the lamp assembly.

    4. Pull the bulb straight from the

    socket.

    Install new bulb(s) in reverse order.

    Replacing high-mount brake lamp bulbs

    1. Make sure the ignition control is

    in the OFF position.

    2. Remove the two screws.

    3. Unclip the bulb holder from the

    reflector.

    4. Pull the bulb straight out.

    Install in reverse order.

    Replacing license plate lamp bulbs

    1. Make sure the headlamp switch is

    in the OFF position.

    2. Remove the screw from the

    license plate lamp assembly and pull

    it down.

    3. Remove bulb socket by turning

    counterclockwise.

    4. Carefully pull the bulb out from

    the socket.

    Install new bulb(s) in reverse order.

    ___end copy___



    You can download your complete owners guide by clicking the link below:

    http://www.motorcraftservice.com/pubs/co鈥?/a>



    Or go to Fords owner website and register yourself and your vehicle for additional info and benefits

    Is it easy to change the tail light on a car?

    Depends on the car.



    Some are easy to get to and just pop out or unscrew.

    Some are harder to get to and need panels removed to change them.

    And some are actually much more expensive and harder to change than you'd think.
    Is it easy to change the tail light on a car?
    dpends on the car. some are pop outs like a light bulb and some need to have little boxes removed to change the light.

    hope you have the easier one.
    Is it easy to change the tail light on a car?
    Generally, yes.

    Some cars you have to remove the Lens, while others are accessible from the trunk of the car.
  • band myspace
  • representative of male teenagers
  • Can someone help with a 93 Buick Regal Tail light problem?

    I have a 93 Buick Regal and the Tail lights will not work, the turn signals work fine, even the stop light on the trunk lid. I have changed the bulbs and still nothing. My turn lever on the steering is alittle wore out, to get the turns to work, I pull it down and pull in just alittle, then they work. Could this have anything to do with the tail lights not working, or is it a short somewhere?
    Can someone help with a 93 Buick Regal Tail light problem?
    Tail lights are on a different circuit than brake and turn signals.



    Do your front and side markers work?



    Either blown fuse, bad switch, or bad relay.



    It's tough to say which one........Sorry.

    Check the easy things first.
    Can someone help with a 93 Buick Regal Tail light problem?
    try fixing the lights and the fuse
    check the switch on the brake pedal
    i check see if you have a bad fuse. then if not. then its a short in the wires.
    There is a short or a ground issue. Get a Chilton's Manuel from your local auto parts and pull the schematic. There you will find where the lights are grounded. Sometimes moisture will corrode the connection and effect the tail lights. Also there is a brake light switch that is between the brake pedal and the colum. There may be a short there also.

    How to replace wiring for a tail light.?

    I own a 2001 Ford Escort and the rear left blinker/brake light does not work. It's not at the blinker switch and it's not at the bulb connector. So it must be a short in the wiring. Is this something I can change myself? If any one knows how to replace the wiring for a tail light in any kind of car, just give me a rough description of how to do it.



    Thanks.
    How to replace wiring for a tail light.?
    try the flasher unit or a possible fuse 1st - more likely than the wiring, unless the wires got damaged or rusted

    How do you change the tail light assy on a 2004 acura tl?

    remove the rear bumper to access the bolts under neath and remove the 8mm nuts in the trunk.

    What are the possible repercussions when the wrong tail light is installed.?

    I have a 97 Ford Explorer. Both tail lights need to be replaced. I went to the wrecking yard. They had two 95's, one 96, one 97 (these models have the same style tail light), all of which had no tail lights. The closest I could find were those of a 94. From 94 to 95 the tail light changed very slightly. It went from a straight edge (where the side panel meets the light) to a slightly rounded edge. The bolting pattern is the same. The height is the same. The width varies due to the curved edge. When the 94 is installed there is a slight gap where the %26quot;curve%26quot; should be. I wonder, to what extent, if any, will this affect the vehicle or the lamp itself. My main concern is water getting into the housing causing shorting or into the exterior frame of the vehicle causing corrosion. How valid are these concerns? What are the other issues I should consider?

    Thank you
    What are the possible repercussions when the wrong tail light is installed.?
    water would be your main concern..
    What are the possible repercussions when the wrong tail light is installed.?
    The seal comes from where the bulb attaches to the housing, not where the assembly bolts to the body. As long as the bulb connectors seal tightly in the assembly as they should, there won't be any problems at all.



    I wouldn't worry about corrosion from water getting into the exterior of the body either. Water gets in there anyway.
    The dimensions of the lamp should be the same, it should fit and be water tight, just the appearance would be off!
    Yeah, water is your big concern, it wont look original. you could put some sealer around the outside if you wanted too.

    How do you change a ford f-250 tail light?

    I popped out the 5/16 bolts and can see two white tabs holding onto the light. I tried prying with a screwdriver but they don't move. It almost looks like you have to unscrew it but I can barely fit a screwdriver in the top one and not even a nail in the bottom one.
    How do you change a ford f-250 tail light?
    If you opened the tailgate and unscrewed (popped???) the two silver torx head screws, then you need to grab it and (pop) it out. Use something plastic with a rag under it to pry against the tail light and bed side.
  • rodents
  • drawing a circle
  • I aksed about my 1994 silverado tail light burning out but I changed left circuit and the brake light started?

    working. that lasted about two weeks. Noe they dont work again. what causes that to happen?
    I aksed about my 1994 silverado tail light burning out but I changed left circuit and the brake light started?
    some where the wires are shorting out where they go through the frame or wiring organizers

    How do you change the brake light in an 05 toyta sienna?

    http://www.autoall.com/images_products/U鈥?/a>



    Thats what it looks like. I can remove the two screws that are visiable but then it appears to still be clipped to the body. I cannot find how to release it so that i can change the tail light.
    How do you change the brake light in an 05 toyta sienna?
    it probably has those plastic clips helping hold it it. if you can get a screwdriver in use it to work the clips out. i worked at a ford dealership and when i had to replace lights i would always get new clips cause its just easier to rip them out and replace with new ones. but make sure you can do that first( get parts first).
    How do you change the brake light in an 05 toyta sienna?
    Buy the replacement.



    From the inside there are plastic parts. Use a screw driver to remove some parts, but most new vehicles have compartments where you can unsnap. It's pretty simple after you see the back of the light.



    Remember to put it all back together in the way you took it apart.

    How do i Change upper tail light bulb on 2001 pt cruiser?

    There should be a manual in the glove box. It will tell you in there. Each car is different

    How much does it cost to change headlights and tail lights?

    I need to change one headlight one tail light and the third light in the back window of my 1994 honda civic ex how much would that cost?
    How much does it cost to change headlights and tail lights?
    Go to any walmart or auto parts store. They'll have a place where you can look up the type of light needed for your car. The lights cost anywhere from $6 and up depending on type and brand. You can probably install them your self for free. Or if you're not comfortable, It only would take 10-20 minutes to replace them, so any car place should be able to do it for around $20.
    How much does it cost to change headlights and tail lights?
    The cost of the bulbs and about a half hour of your time.
    thats cheap man..many people sold that...

    here for ur help..



    http://www.lovemygadget.blogspot.com



    u will find any cheap car there..



    ok

    What size Torx Bit for 2005 Chevy Uplander Tail Light Assembly?

    Not sure why GM would decide to use the more unusual Torx screws on the tail light assembly that the owner is going to periodically need to access but, in order to change a burned out brake light I need to find out what size this thing is...
    What size Torx Bit for 2005 Chevy Uplander Tail Light Assembly?
    27. The torx screws are easier for the assembly line machines to fit. A 1/8 %26quot; allen wrench also fits.
  • Parameter.Add()
  • rodents
  • How to change a burnt out brake light bulb?

    How do you change a tail light bulb in a car?
    How to change a burnt out brake light bulb?
    you need to declare the car and model to find this out.



    Some older cars- take off the lens cap screws and change the bulb.



    newer cars- from the trunk.



    check the owners manual or just google

    %26quot;change brake light 1999 caravan%26quot;
    How to change a burnt out brake light bulb?
    go in the trunk and pull the carpet away from the back of the light...there is usually screws or grommets that you have to pop off and then the bulb slides out. it connects to its socket almost like when you connect a regular cord to an extension cord. the bulb will have the style of bulb that it is. Make sure you get this same kind. If you are really unsure go to an auto parts store and they will help you out.
    how about auto zone and maybe they will do it for ya

    How to change a tail light bulb 2005 jeep grand cherokee?

    open the rear hatch there will be two screws visible take them out pull the housing and it will pop out turn the grey socket to remove the bulb and pop it back in install the two screws Back in and done it takes about five minutes per side

    How do you change the brake light in an 05 toyta sienna?

    I can remove the two screws that are visiable but then it appears to still be clipped to the body. I cannot find how to release it so that i can change the tail light.
    How do you change the brake light in an 05 toyta sienna?
    pivot it away from the body of the car and give it a tug and it will be free
    How do you change the brake light in an 05 toyta sienna?
    Take out the braker fluid, and here is what i do, i replace it with grease. This works every time, and if the car goes out of control, this is not my fault!
    Open the hatch and see if there is a cover panel on the inside of the vehicle. It may be that the bulbs are bayonet mounted from the inside. If there is a cover panel, open it. You will see the wiring and mounting socket. Turn the socket about a quarter turn and it will pop out. You can then replace the bulb and reinsert the socket.



    Good luck.
    Use a small flat screwdriver,gently pry out the back of the light,there are 2 pins which hold the light onto the body by 2 plastic grommets.
    after the 2 bolts are out it pops out to the side. its kinda hard to get good leverage on it. but it goes straight out sideways. you can try to get something between the front of the lens to pull, but watch the paint.

    How to change the tail light bulb on a 2007 Prius?

    RTFM (Read The Fine Manual).
    How to change the tail light bulb on a 2007 Prius?
    you either have to get to it inside the trunk or take the lens off.

    How to change a tail light on 98 ford f 150?

    there are 4 srews 2 behind tailgate 2 on outside corners of light remove screws pull light cover

    light balast willtwist and pull out

    to replace do same in reverse
    How to change a tail light on 98 ford f 150?
    Lower tail gate. Unbolt it, replace it. I don't understand what the problem is.
  • Fish
  • good for enlarged pores
  • How do you change the tail light lens on a 1997 nissan pick-up?

    unscrew the lens and remove and replace
    How do you change the tail light lens on a 1997 nissan pick-up?
    you buy self fix shop, fix your self. work man ship cost 50 sing dollars
    How do you change the tail light lens on a 1997 nissan pick-up?
    If it has a bed liner you will have to partially remove to get to the 10mm screws two on each side that hold the tail light assembly onto the truck. I replace the entire assembly that way moisture won't ruin the bulb contacts and the assembly comes complete with wiring and bulbs.

    Help with tail light on my 1997 honda civic..?

    i just changed the tail lights on my car. the Right 1 had burnt out so i decided to change both. I tested it an pressed the breaks an it still isnt working. the light on left works fine. BUT the one on the right isnt working at all.



    What could be the problem, and how can i fix it. ??



    THANK YOU
    Help with tail light on my 1997 honda civic..?
    check if the wires in the bulbs burned out or always try more than one light bulb and is it the correct one as the burnt out one?

    if the bulbs are burning out then you will have an unwanted resistance meaning there is an electrical wiring problem that something in the wire is exposed or corroded. good luck
    Help with tail light on my 1997 honda civic..?
    you could have a bad wire in your car. does the %26quot;plug in%26quot; spot where the light bulb goes look like its dirty? or like there is corrosion on it? sounds like the only problem you could have since a blown fuse would make BOTH lights not work. hondas are common for havinf corrosion inside the %26quot;bay%26quot; where the bulb goes

    How do you change the tail light of an 05 nissan quest?

    you open the back door and there should be a pannel on it push it or unscrew it whitch ever model u have and take out the light

    2001 volkswagen new beetle need to know how to change a rear tail light?

    i have looked in the owners manual and all it said was to take it a volkswagen dealer and the closest one is over 3 hours away i have the right bulb but i can figure out how to get to the old one to replace it?!?!?!?!
    2001 volkswagen new beetle need to know how to change a rear tail light?
    INSIDE THE HATCH THERE IS AN OVAL ACCESS PANEL

    BEHIND EACH LIGHT.

    TAKE THAT OFF REACH IN AND YOU'LL FIND A KNOB.

    TAKE IT OFF AND CAREFULLY PRY THE WHOLE LIGHT OUT.

    DISCONNECT THE WIRES (JUST A PLUG) AND TAKE THE TAIL LIGHT WHERE YOU CAN WORK TO REPLACE THE BULB.

    ANY CAR WASH SHOULD HAVE A REPLACEMENT.

    GOOD LUCK!

    How do I change the tail lights in a 93 taurus?

    My tail light is out, and I cant seem to access the bulbs. Any help would be appreciated. Oh, and I called some auto places, not too many out there know!
    How do I change the tail lights in a 93 taurus?
    Open the trunk then remove the trim panels in front of the lights. remove the nuts (about 8 of them) pull the whole assembly out the back and you will see where the bulbs are. Change the bulb and check to make sure it works befor you reassemble. Easy to do and shouldn't take more than 15 minutes.
    How do I change the tail lights in a 93 taurus?
    Okay when I need to get a light changed I take it to my auto mechanic that I use for all repairs on my vehicle when it is out of warranty. He then changes the bulb for me and shows me how to do it so that I can do it myself at a later time.
    Go to Pep Boys and get a Chilton's Repair Manual. It will give you step by step instructions with pictures
  • outlook for market
  • my rental property
  • How much will it cost to fix a new ford ka cracked tail light?

    and do you have to take it to a garage to get the light changed?
    How much will it cost to fix a new ford ka cracked tail light?
    take it to a garage if you cant figure out how to do it yourself, itll be the cost of the light , æ‹¢20 from second hand or around æ‹¢50-æ‹¢60 new (depending on year) about æ‹¢20- æ‹¢50 at the MOST to fit it by a garage (do not go main dealer they will be sooooo expensive)
    How much will it cost to fix a new ford ka cracked tail light?
    Ring Ford dealer - they will tell you exactly how much...



    Or



    get one from a scrapyard and fit it yourself - undo the bolts and pop the new one on
    Can be done yourself with a few basic tools and a quick job at a dealer.

    Dealer would be the best place to get one as they have tended to change the design quite a bit over the years and a scrapper might not fit.
    easy to change phone local scappy

    How do I change the bulb in the tail light of a 2005 Volkswage GTI?

    My mom zips me to school, wrestling practice and just about everywhere else in this little car, so I want to do something nice for her. I just can't seem to get the bulb out. Can anyone help me out and give me step-by-step instructions? Thanks!
    How do I change the bulb in the tail light of a 2005 Volkswage GTI?
    Mark L,

    I had a similar problem with my car and i went to Auto Zone and i purchased the bulb from them and they installed it for me at no charge.....I have a freind that did the same thing but at O'Reillys and it was free also, but you have to purchase the bulb from them.....

    How to change a tail light on a 2002 eclipse?

    Dude... open the trunk and look at the back side of the housing TADA...twist off the connector and change the bulb go slow and don't force it....SIMPLE ENOUGH..you might have to move a side panel in your trunk or open an access panel but your ment to be able to get to it....
    How to change a tail light on a 2002 eclipse?
    take it to a repair shop...bring your wallet/purse!

    How do you change a 2001 Isuzu Rodeo Tail light?

    I can't seem to get the light piece off, what's holding it on?
    How do you change a 2001 Isuzu Rodeo Tail light?
    technical manual 2001 isuzu rodeo%26gt;%26gt;tail light, check out some book in the library or search it in the net. look for community forums for your vehicle.
    How do you change a 2001 Isuzu Rodeo Tail light?
    Hey dude chk this out this should help u



    http://www.faqfarm.com/Q/FAQ/892



    http://www.partstrain.com/ShopByDepartme鈥?/a>



    http://www.autoanything.com/grille-guard鈥?/a>



    http://www.carpartswholesale.com/cpw/isu鈥?/a>



    mng.1432@gmail.com

    Where is the tail light fuse on a 2005 Chevy Cobalt?

    My tail lights are out, i changed the bulbs.



    brakes work

    hazards/signals work.

    reverse lights work.

    tail lights dont.



    hazards are same as tail bulbs. hazards work.
    Where is the tail light fuse on a 2005 Chevy Cobalt?
    look in the door of the fuse pannel it should tell u or owners manuel
  • email
  • AJAX in .net
  • Thursday, September 15, 2011

    Why are my tail light running lights not coming on?

    I have a 1996 Chevrolet 1500,The driver side light does not come on at night.The brake light and turning signal works fine.I changed the light bulbs and the circuit board on both sides.but the Night time running light on the driver side does not come on.the passenger side works fine.Like i said i changed both circuit boards and light bulbs.any ideas?
    Why are my tail light running lights not coming on?
    Check the fuses under the hood
    Why are my tail light running lights not coming on?
    Test the wire for B+ If no power check the wiring under the bed for corrosion. Open the wiring loom and you may have to stretch the wire and look/feel for a narrow spot. Corrosion can happen inside the coating with no obvious sign on the outside of the wire.

    How do i change tail light on my 2001 sts?

    Just inside the trunk you will find thumb screws that will release the tail light housing.Pull the housing out to access the tail light bulbs.

    How do i change a tail light for a 1999 pontiac grand am GT?

    Pop the trunk. Pull away the carpet against the rear of the trunk. Twist the light socket. Pull it out. Pull out the bulb. Install new bulb. reverse steps
    How do i change a tail light for a 1999 pontiac grand am GT?
    Peel back the inner liner on the corner, in the trunk, of the side that you need to work on. Behind that liner, you'll see the fasteners that hold the taillamp assembly in place-sometimes they are hex-headed(uses a socket or wrench) and , most times, they're some form of big plastic wingnuts that come out, and the access to the bulbs require removal of the whole assembly(not a big deal)

    How do I change a tail light on an oldsmobile alero?

    the assembly is unbolted from inside the trunk-pull back the carpet and you will see them. remove the nuts and the taillight assembly will come off
    How do I change a tail light on an oldsmobile alero?
    I think you need a special screwdriver from GMC
    How do I change a tail light on an oldsmobile alero?
    speical screwdriver from GM you must be ASE certified and work for a GM dealer to obtain this screwdriver

    How to change the tail light assembly at a Lexus IS300 sportscross wagon 2003?

    my tail light lens is brocken. from the looks of it I need to change the whole assembly
    How to change the tail light assembly at a Lexus IS300 sportscross wagon 2003?
    go on ebay or contact a lexus dealer and ask about pricing and installing including warranty
  • cat
  • loreal hair
  • How can I change the tail light on my Ford Mustang ?It's got a huge crack from a recent accident. Thank you

    You can pop the trunk and peel back the carpet behind the light. Should be a couple of wing nuts, or nuts as well as a connector. undo those and pull out your tail light

    How to change an 05 chevy cobalt tail light?

    my tail light just went out so tomo im going to get a new bulb. I have no experience but it really cant be too hard. My brother who usually handles all my car problems is out of town. So if someone could give me detailed instuctions from beginning to end that'd be great thanks!
    How to change an 05 chevy cobalt tail light?
    get in the trunk and pull the carpet back from the rear of the taillight that needs fixed and you will see 3 or 4 wing nuts that you need to take off and then the light will pull completely out from the outside of the car and then you will see where the bulbs go.
    How to change an 05 chevy cobalt tail light?
    You can probably access the light from the trunk.

    1) Remove the two screws revealed when the trunk lid is opened.

    2) Unscrew upper cargo net anchor.

    3) Pull back carpet wall, remove nut on threaded rod.
    Check in side your trunk...look for a panel that either comes apart by clips or screws. Pull the housing out carefully, your bulb should screw out..the whole thing should be self explanatory. Hope this was helpful.

    How do u change a back tail-light on a 2006 Pontiac G6?

    open trunk, pull carpet back from rear taillight area and you will see probably 4 wing nuts that hold the light assembly in, take the wing nuts off and pull the light out and then you will see.
    How do u change a back tail-light on a 2006 Pontiac G6?
    If you go to the library they have books on car repair that you can check out. They are specific to year, make, and model, have easy to follow instructions, and even pictures to help you out. Chilton's makes them, and also some other companies.



    Otherwise you can check your owners manual.

    Want to know how to remove rear tail light on 89 chevy celebrity to change light?

    need to check wires %26amp; bulb on 89 celebrity tail light
    Want to know how to remove rear tail light on 89 chevy celebrity to change light?
    The bulb %26quot;should%26quot; be able to be removed from inside.

    Unplug it.

    turn it 1/4, jiggle and pull.



    You might have to remove some plastic cover to get to it.

    But it's pretty simple.
    Want to know how to remove rear tail light on 89 chevy celebrity to change light?
    I will assume you are talking about the bulb, not the entire housing/ lens. Open your trunk, you will see wires going to a socket in the interior housing. Rotate the socket about 1/4 turn to the left (you will feel it loosen), pull it straight out to check/replace the bulb. To reinstall, reverse the procedure.
    can you get to the bulb by opening the trunk?
    i bet your manual knows ;)

    How to change my tail light on my VW bettle 01?

    Ok go into your trunk and which ever side it is on bend into the trunk and there should be a cutout of plastic that pops out you may need a screw driver to get it out. And then just replace which ever light is blown.
    How to change my tail light on my VW bettle 01?
    Look in your owners manual if you still have it and it will tell you in there. If you do not have one call a parts place and they should be able to help you out.
  • connecting database
  • is there a lestateboomover
  • How do you change a tail light bulb on a Peugeot 206 on a W reg?

    In your boot there should get access to your lights via a plastic panel. When you remove the panel the lights should be easily accessed, carefully take the defected light out and changed with a new one. Check your vechiles manual or go to the Hayes online site and just type in your make and model and the problem and it should come on screen how to do it.

    I am trying to change a rear tail light on a 92 Lexus SC400. how do i get the tail light lens off?

    i know that entry is through the trunk under the carpet, but i am having trouble locating the right nuts and bolts to loosen. anyone have any pointers?
    I am trying to change a rear tail light on a 92 Lexus SC400. how do i get the tail light lens off?
    You don't have to take the lens off, the bulbs pop in the holders that are fitted into the sockets inside the trunk.

    How do I remove tail light cover on 2006 Silverado to change break light bulb.?

    there should be some screws inside the bed to loosen the lens

    How do you change a burnt out tail light in a 09 Buick Enclave?

    My wife's enclave has a burnt out taillight.. How do you change the bulb ? I don't see how to take the lens off or remove the light Assembly. It is NOTHING like my 67 Firebird. HELP ?!
    How do you change a burnt out tail light in a 09 Buick Enclave?
    take it to autozone and act (sic) like a dumb blonde, they may put it in for you
    How do you change a burnt out tail light in a 09 Buick Enclave?
    very carefully

    How do you change the tail light or backlight of nissan sentra 1.8s 2005?

    hey my right taillight broke and i want to change it myself. i can get the taillight on ebay but how to change it please help?
    How do you change the tail light or backlight of nissan sentra 1.8s 2005?
    i own a repair shop,and all you do is raise the trunk lid and remove the back panel for that side ,and you,ll see a bunch of nuts on the back side of the light these are what hold it in ,be careful and don't break none of these off ,they might may be stuck some but it will come out,make sure you have all the nuts off if it though,it has a few of them on it,and be careful putting the new one back in,its an easy job,take your time and you,ll do fine with it,good luck,i hope this help,s.
    How do you change the tail light or backlight of nissan sentra 1.8s 2005?
    your welcome.

    Report Abuse


    sinse when did nissan have a model called the sentra,sure you dont mean Cedric?Vauxhall had a sentra.
    open trunk and take off cover behind light remove bulb by turning the bulb socket and then pull out.
  • Making my own duvet cover
  • software
  • How do I change my rear tail light of a 2006 Dodge Grand Caravan? It doesn't seem to have any access points.

    Is the cover 'pop-off'?
    How do I change my rear tail light of a 2006 Dodge Grand Caravan? It doesn't seem to have any access points.
    open the liftgate. you will see 2 black plastic push pins. remove these. now you can remove the housing by pulling rearward. replace bulb.
    How do I change my rear tail light of a 2006 Dodge Grand Caravan? It doesn't seem to have any access points.
    it's in the owners manual
    Go to your local Autozone or Advance Auto Parts and ask. 9 times out of 10, they'll crack open a Haynes manual and find the section that tells you how.
    Check the owners manual. We have a few for those minivans at work, and if I recall it's inside the cabin, around where the back part of where the rear lights should be look for a plastic cover. Usually all you need to do is pop that off, use a screw driver if you need to, and that should be your access point to change bulbs, and the screws that hold the housing should be accessible there also.
    look directly behind the light on the inside of it,there should be a cover that will pop off if it,and that will give you access to the tail light on it,it also may tell about this in the owners manual ,good luck.
    open the tail gate and remove the covers in the corners , you'll find your bulb sockets right there